UA-76780267-1
  Loading... Please wait...
  • Image 1
  • Image 2
  • Image 3
  • Image 4
  • Image 5

Kamotors Canyon Crusher V2 T4 turbo kit

$3,650.00

Product Description

 NO RETURNS WHAT SO EVER ON THESE MADE TO ORDER TURBO KITS

 

     This is the newest turbo kit from Kamotors Performance. The Canyon Crusher V2 turbo kit features the same large t4 turbo as v1; That will achieve up to 10psi in first gear with 3.73 rear diff; and will reach positive pressure in 3rd gear at 3100rpms. But V2's Real changes come from the simplified charge pipes,  You get half the piping length, with smoother bends and transitions. This reduces weight, increases response time and allows the kit to install with ease. This kit still uses the massive intercooler but now its mounted up higher allowing for the use of oil coolers as well.

 

An excellent turbo setup for High speed events where RPM's are easily kept above 2500.
*Manifold-clears factory oil cooler lines and A/C at the block, But my charge piping will not fit with Air conditioning.( we can sell a kit with universal charge piping for those who want to try to keep A/C) Intercooler sits down low in the valance so one 325i models you'll need to either Remove or relocate your oil cooler.BMW Part #11112140435 will delete the oil cooler.
*Precision 6262 t4 .84A/r turbocharger.
Compressor Wheel Inducer: 62mm
Exhaust Housing A/R: .84
Exhaust Housing Inlet: T4 Divided "Twin Scroll"
Exhaust Housing Outlet: V-Band
Compressor Housing: "SP" - 4.0"/2.5" Ported Shroud
Bearing Type: Journal Bearing
HP Rating: 680-700
*(OPTIONAL)-PNP MS2 ECU, IAT sensor and with All new Base Tune+ 
-better dialed in Base tune.New base tune has better calibrated warmup enrichment, Barometric correction, Fuel and ignition table as well as wasted spark, launch control and flat foot shifting capabilities.

*Oil feed and drain

*Oil sandwhich feed plate

*TRE PNP 60lb Fuel injectors(as of 12/30/16)

*All new Rapid spool Industries t4 manifold

*Huge Front mount intercooler (will require massaging and minor trimming)

*Precision 46mm external Wastegate

*charge piping, silicone couplers, reducers and clamps.(BOV is no longer included or used in my setup, customers can add one if they desire.)

 

This kit is designed to work on 100% original bottom end and has been personally tested to boost levels between 1-17psi. I have done testing upto 20psi but am not comfortalbe running that much power on a stock motor.

 

A brand new factory clutch held around 10psi, I personally run a clutchmasters fx400 and it holds 17psi without issue.

This kit has also been fully dyno tested at various boost levels!

All testing was done on a Mustang dyno, with only minor fueling changes from the base tune I supply with my kit.

- 330whp at 13-14psi

- 396whp at 16psi

- 401whp and 370trq at 17psi.

 

 

This kit is made to order please allow 2weeks for shipment w/out ECU and 3 weeks for kit with ECU.

Product Videos

BMW E30 Turbo Part 3 Shakedown 01:39

Well decided not to time lapse the rest of the process as it was a lot of me redesigning, cutting, drawing and sitting there thinking vs. actual work. But I did film the end results of some hard work. I completely redesigned the turbo kit for less weight, greater efficiency, better fit, and for a greater ease of install. Will be releasing this new turbo kit at kamotorsperformance.com

  • BMW E30 Turbo ...
    Well decided not to time lapse the rest of the process as it w...

Product Reviews

Write Review

This product hasn't received any reviews yet. Be the first to review this product!

Quantity: